visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model C1517J5003AHF rev d ultra low profile 0805 3 db, 90 hybrid coupler description the C1517J5003AHF is a low cost, low p rofile subminiature high performance 3 db coupler in an easy to use surface mount package. the C1517J5003AHF is ideal for balanced power and low n oise amplifiers, plus signal distribution and other applications where low inser tion loss and tight amplitude and phase balance are required. the C1517J5003AHF is a vailable on tape and reel for pick and place high volume manufacturing. all of the xinger components are construc ted from ceramic filled ptfe composites which possess excellent electrical and m echanical stability. all parts have been subjected to rigorous qualification testi ng and units are 100% rf tested. detailed electrical specifications: specifications subject to change without notice. features: ? 1500 C 1700 mhz ? 0.7mm height profile ? high isolation & low loss ? lte bands: 24 ? surface mountable ? tape & reel ? non-conductive surface ? rohs compliant ? halogen-free ? 100% rf tested ? - 55c to 85c room (25 c) parameter min. typ. max unit frequency 1500 1700 mhz port impedance 50 return loss 21 25 db isolation 24 28 db insertion loss* 0.2 0.3 db amplitude balance 0.4 1.0 db phase balance (relative to 90) 0.7 4 degrees power handling 4 watts operating temperature 55 +85 oc group delay (1.5-1.7ghz) (nsec) min. typ. max 0.093 0.108 0.123 * insertion loss stated at room temperature (insert ion loss is approximately 0.1 db higher at +85 oc) outline drawing top view (nearside) 1.290.10 2.040.10 orientation marker denotes pin location side view 0.700.07 bottom view (farside) 2x 0.15 6x 0.98 4x 0.65 6x 0.30 6x 0.22 orientation marker denotes pin location 4x 0.37 6 5 4 3 2 1 configuration1 input gnd isolated direct gnd coupled 5 4 2 16 3 pin configuration2 isolated gnd input coupled gnd direct configuration3 direct gnd coupled input gnd isolated configuration4 coupled gnd direct isolated gnd input mechanical outline dimensions are in millimeters tolerances are noncumulative
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model C1517J5003AHF rev d typical broadband performance: 500 mhz. to 6000 mhz . 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 35 30 25 20 15 10 5 0 return loss at input port (db) freq [ghz] return loss at input port (db) 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 3.5 3 2.5 2 1.5 1 0.5 0 insertion loss (db) freq [ghz] insertion loss (db) 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 2 1.5 1 0.5 0 0.5 1 1.5 2 amplitude balance (db) freq [ghz] amplitude balance (db) 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 20 15 10 5 0 5 10 15 20 phase balance(degree) freq [ghz] phase balance(degree) 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 35 30 25 20 15 10 5 0 isolation (db) freq [ghz] isolation (db)
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model C1517J5003AHF rev d typical performance: 1400 mhz. to 1800 mhz. 1.4 1.45 1.5 1.55 1.6 1.65 1.7 1.75 1.8 35 30 25 20 15 10 5 0 return loss at input port (db) freq [ghz] return loss at input port (db) 1.4 1.45 1.5 1.55 1.6 1.65 1.7 1.75 1.8 3.5 3 2.5 2 1.5 1 0.5 0 insertion loss (db) freq [ghz] insertion loss (db) 1.4 1.45 1.5 1.55 1.6 1.65 1.7 1.75 1.8 2 1.5 1 0.5 0 0.5 1 1.5 2 amplitude balance (db) freq [ghz] amplitude balance (db) 1.4 1.45 1.5 1.55 1.6 1.65 1.7 1.75 1.8 10 8 6 4 2 0 2 4 6 8 10 phase balance(degree) freq [ghz] phase balance(degree) 1.4 1.45 1.5 1.55 1.6 1.65 1.7 1.75 1.8 35 30 25 20 15 10 5 0 isolation (db) freq [ghz] isolation (db)
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model C1517J5003AHF rev d definition of measured specifications * 100% rf test is performed per spec definition for p in configuration 1 and port 1 (input port) is conne cted to pin1, port 2 (isolated port) is connected t o pin 3, port 3 (direct port) is connected to pin 4 a nd port 4 (isolated) is connected to pin 6 . parameter definition mathematical representation i , j , k , m is denoted as the port index of input, isolated, d irect and coupled port for specific pin configuration sho wn in the table return loss the impedance match of the coupler to a 50 system. return loss is an alternate means to express vswr. 10 20 log ( ) ii s isolation the input power divided by the sum of the power at the two output ports. 10 20log ji s insertion loss the input power divided by the sum of the power at the two output ports. 2 2 10 10 log ( ) mi ki s s + amplitude balance the difference in power between the two outputs. 10 20log ( ) ki mi s s phase balance the difference in phase angle between the two output ports. 90 o ki mi s s ? + group delay group delay is defined as the average of the mean group delay of the coupling path and the mean group delay of the direct path. group delay (ns) = ( ) ( ) ( ) ( ) 2 mi ki mean gd s mean gd s + where " " mean is the arithmetic mean of the group delay over a frequency band.
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model C1517J5003AHF rev d mounting configuration: in order for xinger surface mount components to wor k optimally, the proper impedance transmission line s must be used to connect to the rf ports. if this condition is not satisfied, insertion loss, isolation and vs wr may not meet published specifications. all of the xinger components are constructed from o rganic ptfe based composites which possess excellen t electrical and mechanical stability. xinger compone nts are compliant to a variety of rohs and green st andards and ready for pbfree soldering processes. pads are gol d plated with a nickel barrier. an example of the pcb footprint used in the testing of these parts is shown below. in specific design s, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. mounting footprint dimensions are in millimeters plated thru holes to ground circuit pattern footprint pad (s) solder resist 4x transmission line 4x 0.30 6x 0.35 6x 0.33 6x 0.05 0.66
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model C1517J5003AHF rev d packaging and ordering information parts are available in reel and are packaged per ei a 4812. parts are oriented in tape and reel as sh own below. minimum order quantities are 4000 per reel. see mo del numbers below for further ordering information . 1.75 3.50 4.00 1.60 .81 8.00 4.00 2.00 .25 2.41
|
